APU Platform
APU1C4
APU1C Cooling Assembly
Compex WLE200NX a/b/g/n miniPCI express radio card
FreeBSD – Status of Atheros Wifi Hardware
Enclosure 3 LAN USB black
PC Engines APU1C – A review
APU1C Review
BIOS
PC Engines APU BIOS build date: Apr 5 2014 Reading data from file [bootorder] SeaBIOS (version ?-20140405_120742-frink) SeaBIOS (version ?-20140405_120742-frink) Found coreboot cbmem console @ df150400 Found mainboard PC Engines APU Relocating init from 0x000e8e71 to 0xdf1065e0 (size 39259) Found CBFS header at 0xfffffb90 found file "bootorder" in cbmem CPU Mhz=1000 Found 29 PCI devices (max PCI bus is 06) Copying PIR from 0xdf160400 to 0x000f27a0 Copying MPTABLE from 0xdf161400/df161410 to 0x000f25a0 with length 1f4 Copying ACPI RSDP from 0xdf162400 to 0x000f2580 Copying SMBIOS entry point from 0xdf16d800 to 0x000f2560 Using pmtimer, ioport 0x808 Scan for VGA option rom EHCI init on dev 00:12.2 (regs=0xf7f08420) Found 1 lpt ports Found 2 serial ports AHCI controller at 11.0, iobase f7f08000, irq 11 EHCI init on dev 00:13.2 (regs=0xf7f08520) EHCI init on dev 00:16.2 (regs=0xf7f08620) Searching bootorder for: /pci@i0cf8/*@11/drive@0/disk@0 AHCI/0: registering: "AHCI/0: SB mSATA SSD ATA-10 Hard-Disk (14318 MiBytes)" Searching bootorder for: /rom@img/setup Searching bootorder for: /rom@img/memtest OHCI init on dev 00:12.0 (regs=0xf7f04000) OHCI init on dev 00:13.0 (regs=0xf7f05000) OHCI init on dev 00:14.5 (regs=0xf7f06000) OHCI init on dev 00:16.0 (regs=0xf7f07000) Searching bootorder for: /pci@i0cf8/usb@16,2/storage@1/*@0/*@0,0 Searching bootorder for: /pci@i0cf8/usb@16,2/usb-*@1 USB MSC vendor='Multiple' product='Card Reader' rev='1.00' type=0 removable=1 Device reports MEDIUM NOT PRESENT scsi_is_ready returned -1 Unable to configure USB MSC drive. Unable to configure USB MSC device. All threads complete. Scan for option roms Running option rom at c000:0003 iPXE (http://ipxe.org) 00:00.0 C000 PCI2.10 PnP PMMpmm call arg1=1 pmm call arg1=0 +DF0E2FD0pmm call arg1=1 pmm call arg1=0 +DF042FD0 C000 Press Ctrl-B to configure iPXE (PCI 00:00.0)... Searching bootorder for: /rom@genroms/pxeboot.rom Build date: Apr 5 2014 System memory size: 4592 MB Press F12 for boot menu. Select boot device: 1. USB MSC Drive Multiple Card Reader 1.00 2. AHCI/0: SB mSATA SSD ATA-10 Hard-Disk (14318 MiBytes) 3. iPXE (PCI 00:00.0) 4. Payload [setup] 5. Payload [memtest] Searching bootorder for: HALT drive 0x000f24f0: PCHS=16383/16/63 translation=lba LCHS=1024/255/63 s=29323728 Space available for UMB: c1000-ee800, f0000-f24f0 Returned 253952 bytes of ZoneHigh e820 map has 7 items: 0: 0000000000000000 - 000000000009fc00 = 1 RAM 1: 000000000009fc00 - 00000000000a0000 = 2 RESERVED 2: 00000000000f0000 - 0000000000100000 = 2 RESERVED 3: 0000000000100000 - 00000000df14e000 = 1 RAM 4: 00000000df14e000 - 00000000e0000000 = 2 RESERVED 5: 00000000f8000000 - 00000000f9000000 = 2 RESERVED 6: 0000000100000000 - 000000011f000000 = 1 RAM enter handle_19: NULL
Booting from Hard Disk... Booting from 0000:7c00
Booting from Hard Disk... Boot failed: not a bootable disk enter handle_18: NULL Booting from ROM... Booting from c000:0363 iPXE (PCI 00:00.0) starting execution...ok iPXE initialising devices...ok iPXE 1.0.0+ -- Open Source Network Boot Firmware -- http://ipxe.org Features: HTTP iSCSI DNS TFTP AoE bzImage ELF MBOOT PXE PXEXT Menu net0: 00:0d:b9:35:88:b4 using rtl8168 on PCI01:00.0 (open) [Link:down, TX:0 TXE:0 RX:0 RXE:0] [Link status: Down (http://ipxe.org/38086101)] Waiting for link-up on net0................
APU Board BIOS issues
Bug 188877 – powernow doesn’t attach on AMD G-T40E
General
Unpacking and Assembling PC Engines’ APU – Part 1
PC Engines mit neuem APU System Board
FreeBSD
Installing FreeBSD 10 on an alix apu.1c4
Installing FreeBSD 10.0 NanoBSD on a Soekris net6501
Using a Solid State Drive with FreeBSD
PC Engines APU dmesg + pciconf
DTrace on FreeBSD
FreeBSD Handbook / Handbuch
2.3. Pre-Installation Tasks ==> Writing an Image File to USB
32.8. Plattenloser Betrieb mit PXE
25.6. Setting Up the Serial Console
25.3.1. Terminal Configuration
______ ____ _____ _____ | ____| | _ \ / ____| __ \ | |___ _ __ ___ ___ | |_) | (___ | | | | | ___| '__/ _ \/ _ \| _ < \___ \| | | | | | | | | __/ __/| |_) |____) | |__| | | | | | | | || | | | |_| |_| \___|\___||____/|_____/|_____/ ``` ` s` `.....---.......--.``` -/ +------------Welcome to FreeBSD-----------+ +o .--` /y:` +. | | yo`:. : `+- | 1. Boot Multi User [Enter] | y/ -/` -o/ | 2. Boot [S]ingle User | .- ::/sy+:. | 3. [Esc]ape to loader prompt | / `-- / | 4. Reboot | `: :` | | `: :` | Options: | / / | 5. Configure Boot [O]ptions... | .- -. | | -- -. | | `:` `:` | | .-- `--. | | .---.....----. +-----------------------------------------+ Booting... Copyright (c) 1992-2014 The FreeBSD Project. Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 The Regents of the University of California. All rights reserved. FreeBSD is a registered trademark of The FreeBSD Foundation. FreeBSD 10.0-RELEASE #0 r260789: Thu Jan 16 22:34:59 UTC 2014 root@snap.freebsd.org:/usr/obj/usr/src/sys/GENERIC amd64 FreeBSD clang version 3.3 (tags/RELEASE_33/final 183502) 20130610 CPU: AMD G-T40E Processor (1000.02-MHz K8-class CPU) Origin = "AuthenticAMD" Id = 0x500f20 Family = 0x14 Model = 0x2 Stepping = 0 Features=0x178bfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,MMX,FXSR,SSE,SSE2,HTT> Features2=0x802209<SSE3,MON,SSSE3,CX16,POPCNT> AMD Features=0x2e500800<SYSCALL,NX,MMX+,FFXSR,Page1GB,RDTSCP,LM> AMD Features2=0x35ff<LAHF,CMP,SVM,ExtAPIC,CR8,ABM,SSE4A,MAS,Prefetch,IBS,SKINIT,WDT> TSC: P-state invariant, performance statistics real memory = 4815060992 (4592 MB) avail memory = 4087570432 (3898 MB) Event timer "LAPIC" quality 400 ACPI APIC Table: <CORE COREBOOT> FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs FreeBSD/SMP: 1 package(s) x 2 core(s) cpu0 (BSP): APIC ID: 0 cpu1 (AP): APIC ID: 1 random device not loaded; using insecure entropy ioapic0 <Version 2.1> irqs 0-23 on motherboard kbd0 at kbdmux0 random: <Software, Yarrow> initialized module_register_init: MOD_LOAD (vesa, 0xffffffff80cfa5e0, 0) error 19 acpi0: <CORE COREBOOT> on motherboard acpi0: Power Button (fixed) cpu0: <ACPI CPU> on acpi0 cpu1: <ACPI CPU> on acpi0 atrtc0: <AT realtime clock> port 0x70-0x71 irq 8 on acpi0 Event timer "RTC" frequency 32768 Hz quality 0 attimer0: <AT timer> port 0x40-0x43 irq 0 on acpi0 Timecounter "i8254" frequency 1193182 Hz quality 0 Event timer "i8254" frequency 1193182 Hz quality 100 Timecounter "ACPI-fast" frequency 3579545 Hz quality 900 acpi_timer0: <32-bit timer at 3.579545MHz> port 0x808-0x80b on acpi0 hpet0: <High Precision Event Timer> iomem 0xfed00000-0xfed003ff on acpi0 Timecounter "HPET" frequency 14318180 Hz quality 950 Event timer "HPET" frequency 14318180 Hz quality 550 Event timer "HPET1" frequency 14318180 Hz quality 450 pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff iomem 0xa0000-0xbffff on acpi0 pci0: <ACPI PCI bus> on pcib0 pcib1: <ACPI PCI-PCI bridge> irq 16 at device 4.0 on pci0 pci1: <ACPI PCI bus> on pcib1 re0: <RealTek 8168/8111 B/C/CP/D/DP/E/F/G PCIe Gigabit Ethernet> port 0x1000-0x10ff mem 0xf7900000-0xf7900fff,0xf7800000-0xf7803fff irq 16 at device 0.0 on pci1 re0: Using 1 MSI-X message re0: ASPM disabled re0: Chip rev. 0x2c000000 re0: MAC rev. 0x00200000 miibus0: <MII bus> on re0 rgephy0: <RTL8169S/8110S/8211 1000BASE-T media interface> PHY 1 on miibus0 rgephy0: none, 10baseT, 10baseT-FDX, 10baseT-FDX-flow, 100baseTX, 100baseTX-FDX, 100baseTX-FDX-flow, 1000baseT, 1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, 1000baseT-FDX-flow, 1000baseT-FDX-flow-master, auto, auto-flow re0: Ethernet address: 00:0d:b9:35:88:b4 pcib2: <ACPI PCI-PCI bridge> irq 17 at device 5.0 on pci0 pci2: <ACPI PCI bus> on pcib2 re1: <RealTek 8168/8111 B/C/CP/D/DP/E/F/G PCIe Gigabit Ethernet> port 0x2000-0x20ff mem 0xf7b00000-0xf7b00fff,0xf7a00000-0xf7a03fff irq 17 at device 0.0 on pci2 re1: Using 1 MSI-X message re1: ASPM disabled re1: Chip rev. 0x2c000000 re1: MAC rev. 0x00200000 miibus1: <MII bus> on re1 rgephy1: <RTL8169S/8110S/8211 1000BASE-T media interface> PHY 1 on miibus1 rgephy1: none, 10baseT, 10baseT-FDX, 10baseT-FDX-flow, 100baseTX, 100baseTX-FDX, 100baseTX-FDX-flow, 1000baseT, 1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, 1000baseT-FDX-flow, 1000baseT-FDX-flow-master, auto, auto-flow re1: Ethernet address: 00:0d:b9:35:88:b5 pcib3: <ACPI PCI-PCI bridge> irq 18 at device 6.0 on pci0 pci3: <ACPI PCI bus> on pcib3 re2: <RealTek 8168/8111 B/C/CP/D/DP/E/F/G PCIe Gigabit Ethernet> port 0x3000-0x30ff mem 0xf7d00000-0xf7d00fff,0xf7c00000-0xf7c03fff irq 18 at device 0.0 on pci3 re2: Using 1 MSI-X message re2: ASPM disabled re2: Chip rev. 0x2c000000 re2: MAC rev. 0x00200000 miibus2: <MII bus> on re2 rgephy2: <RTL8169S/8110S/8211 1000BASE-T media interface> PHY 1 on miibus2 rgephy2: none, 10baseT, 10baseT-FDX, 10baseT-FDX-flow, 100baseTX, 100baseTX-FDX, 100baseTX-FDX-flow, 1000baseT, 1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, 1000baseT-FDX-flow, 1000baseT-FDX-flow-master, auto, auto-flow re2: Ethernet address: 00:0d:b9:35:88:b6 pcib4: <ACPI PCI-PCI bridge> irq 19 at device 7.0 on pci0 pci4: <ACPI PCI bus> on pcib4 ath0: <Atheros 9280> at device 0.0 on pci4 [ath] enabling AN_TOP2_FIXUP ath0: [HT] enabling HT modes ath0: [HT] 1 stream STBC receive enabled ath0: [HT] 1 stream STBC transmit enabled ath0: [HT] 2 RX streams; 2 TX streams ath0: AR9280 mac 128.2 RF5133 phy 13.0 ath0: 2GHz radio: 0x0000; 5GHz radio: 0x00c0 ahci0: <ATI IXP700 AHCI SATA controller> port 0x4010-0x4017,0x4020-0x4023,0x4018-0x401f,0x4024-0x4027,0x4000-0x400f mem 0xf7f08000-0xf7f083ff irq 19 at device 17.0 on pci0 ahci0: AHCI v1.20 with 6 6Gbps ports, Port Multiplier supported ahcich0: <AHCI channel> at channel 0 on ahci0 ahcich1: <AHCI channel> at channel 1 on ahci0 ahcich2: <AHCI channel> at channel 2 on ahci0 ahcich3: <AHCI channel> at channel 3 on ahci0 ahcich4: <AHCI channel> at channel 4 on ahci0 ahcich5: <AHCI channel> at channel 5 on ahci0 ohci0: <AMD SB7x0/SB8x0/SB9x0 USB controller> mem 0xf7f04000-0xf7f04fff irq 18 at device 18.0 on pci0 usbus0 on ohci0 ehci0: <AMD SB7x0/SB8x0/SB9x0 USB 2.0 controller> mem 0xf7f08400-0xf7f084ff irq 17 at device 18.2 on pci0 usbus1: EHCI version 1.0 usbus1 on ehci0 ohci1: <AMD SB7x0/SB8x0/SB9x0 USB controller> mem 0xf7f05000-0xf7f05fff irq 18 at device 19.0 on pci0 usbus2 on ohci1 ehci1: <AMD SB7x0/SB8x0/SB9x0 USB 2.0 controller> mem 0xf7f08500-0xf7f085ff irq 17 at device 19.2 on pci0 usbus3: EHCI version 1.0 usbus3 on ehci1 pci0: <serial bus, SMBus> at device 20.0 (no driver attached) isab0: <PCI-ISA bridge> at device 20.3 on pci0 isa0: <ISA bus> on isab0 pcib5: <ACPI PCI-PCI bridge> at device 20.4 on pci0 pci5: <ACPI PCI bus> on pcib5 ohci2: <AMD SB7x0/SB8x0/SB9x0 USB controller> mem 0xf7f06000-0xf7f06fff irq 18 at device 20.5 on pci0 usbus4 on ohci2 pcib6: <ACPI PCI-PCI bridge> at device 21.0 on pci0 pci6: <ACPI PCI bus> on pcib6 ohci3: <AMD SB7x0/SB8x0/SB9x0 USB controller> mem 0xf7f07000-0xf7f07fff at device 22.0 on pci0 usbus5 on ohci3 ehci2: <AMD SB7x0/SB8x0/SB9x0 USB 2.0 controller> mem 0xf7f08600-0xf7f086ff at device 22.2 on pci0 usbus6: EHCI version 1.0 usbus6 on ehci2 acpi_button0: <Power Button> on acpi0 orm0: <ISA Option ROM> at iomem 0xee800-0xeffff on isa0 ppc0: cannot reserve I/O port range uart0: <16550 or compatible> at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0 uart0: console (9600,n,8,1) uart1: <16550 or compatible> at port 0x2f8-0x2ff irq 3 on isa0 acpi_throttle0: <ACPI CPU Throttling> on cpu0 acpi_throttle1: <ACPI CPU Throttling> on cpu1 acpi_throttle1: failed to attach P_CNT device_attach: acpi_throttle1 attach returned 6 Timecounters tick every 1.000 msec random: unblocking device. usbus0: 12Mbps Full Speed USB v1.0 usbus1: 480Mbps High Speed USB v2.0 ugen0.1: <ATI> at usbus0 uhub0: <ATI OHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus0 ugen1.1: <ATI> at usbus1 uhub1: <ATI EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus1 usbus2: 12Mbps Full Speed USB v1.0 usbus3: 480Mbps High Speed USB v2.0 ugen2.1: <ATI> at usbus2 uhub2: <ATI OHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus2 ugen3.1: <ATI> at usbus3 uhub3: <ATI EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus3 usbus4: 12Mbps Full Speed USB v1.0 usbus5: 12Mbps Full Speed USB v1.0 ugen4.1: <ATI> at usbus4 uhub4: <ATI OHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus4 ugen5.1: <ATI> at usbus5 uhub5: <ATI OHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus5 usbus6: 480Mbps High Speed USB v2.0 uhub0: 5 ports with 5 removable, self powered ugen6.1: <ATI> at usbus6 uhub6: <ATI EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus6 uhub4: 2 ports with 2 removable, self powered uhub2: 5 ports with 5 removable, self powered ada0 at ahcich0 bus 0 scbus0 target 0 lun 0 ada0: <SB mSATA SSD S9FM01.8> ATA-10uhub5: 4 ports with 4 removable, self powered SATA 3.x device ada0: Serial Number DDDF074704EE00609569 ada0: 600.000MB/s transfers (SATA 3.x, UDMA6, PIO 8192bytes) ada0: Command Queueing enabled ada0: 14318MB (29323728 512 byte sectors: 16H 63S/T 16383C) ada0: Previously was known as ad4 Netvsc initializing... SMP: AP CPU #1 Launched! Timecounter "TSC" frequency 1000021734 Hz quality 800 Root mount waiting for: usbus6 usbus3 usbus1 uhub1: 5 ports with 5 removable, self powered uhub3: 5 ports with 5 removable, self powered uhub6: 4 ports with 4 removable, self powered Root mount waiting for: usbus6 ugen6.2: <Generic> at usbus6 umass0: <Generic Flash Card ReaderWriter, class 0/0, rev 2.01/1.00, addr 2> on usbus6 umass0: SCSI over Bulk-Only; quirks = 0x4001 Root mount waiting for: usbus6 umass0:6:0:-1: Attached to scbus6 da0 at umass-sim0 bus 0 scbus6 target 0 lun 0 da0: <Multiple Card Reader 1.00> Removable Direct Access SCSI-4 device da0: Serial Number 058F63666485 da0: 40.000MB/s transfers da0: 3781MB (7744512 512 byte sectors: 255H 63S/T 482C) da0: quirks=0x2<NO_6_BYTE> Trying to mount root from ufs:/dev/ufs/FreeBSD_Install [ro,noatime]... Entropy harvesting: interrupts ethernet point_to_point swi. Starting file system checks: /dev/ufs/FreeBSD_Install: FILE SYSTEM CLEAN; SKIPPING CHECKS /dev/ufs/FreeBSD_Install: clean, 43992 free (232 frags, 5470 blocks, 0.0% fragmentation) Mounting local file systems:. Writing entropy file:. /etc/rc: WARNING: $hostname is not set -- see rc.conf(5). Starting Network: lo0 re0 re1 rere0: link state changed to DOWN 2. lo0: flags=8re1: link state changed to DOWN 049<UP,LOOPBACK,re2: link state changed to DOWN RUNNING,MULTICAST> metric 0 mtu 16384 options=600003<RXCSUM,TXCSUM,RXCSUM_IPV6,TXCSUM_IPV6> inet6 ::1 prefixlen 128 inet6 fe80::1%lo0 prefixlen 64 scopeid 0x5 inet 127.0.0.1 netmask 0xff000000 nd6 options=21<PERFORMNUD,AUTO_LINKLOCAL> re0: flags=8802<BROADCAST,SIMPLEX,MULTICAST> metric 0 mtu 1500 options=8209b<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,VLAN_HWCSUM,WOL_MAGIC,LINKSTATE> ether 00:0d:b9:35:88:b4 nd6 options=29<PERFORMNUD,IFDISABLED,AUTO_LINKLOCAL> media: Ethernet autoselect (10baseT/UTP <half-duplex>) status: no carrier re1: flags=8802<BROADCAST,SIMPLEX,MULTICAST> metric 0 mtu 1500 options=8209b<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,VLAN_HWCSUM,WOL_MAGIC,LINKSTATE> ether 00:0d:b9:35:88:b5 nd6 options=29<PERFORMNUD,IFDISABLED,AUTO_LINKLOCAL> media: Ethernet autoselect (10baseT/UTP <half-duplex>) status: no carrier re2: flags=8802<BROADCAST,SIMPLEX,MULTICAST> metric 0 mtu 1500 options=8209b<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,VLAN_HWCSUM,WOL_MAGIC,LINKSTATE> ether 00:0d:b9:35:88:b6 nd6 options=29<PERFORMNUD,IFDISABLED,AUTO_LINKLOCAL> media: Ethernet autoselect (10baseT/UTP <half-duplex>) status: no carrier Starting devd. Starting Network: re0. re0: flags=8802<BROADCAST,SIMPLEX,MULTICAST> metric 0 mtu 1500 options=8209b<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,VLAN_HWCSUM,WOL_MAGIC,LINKSTATE> ether 00:0d:b9:35:88:b4 nd6 options=29<PERFORMNUD,IFDISABLED,AUTO_LINKLOCAL> media: Ethernet autoselect (10baseT/UTP <half-duplex>) status: no carrier Starting Network: re1. re1: flags=8802<BROADCAST,SIMPLEX,MULTICAST> metric 0 mtu 1500 options=8209b<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,VLAN_HWCSUM,WOL_MAGIC,LINKSTATE> ether 00:0d:b9:35:88:b5 nd6 options=29<PERFORMNUD,IFDISABLED,AUTO_LINKLOCAL> media: Ethernet autoselect (10baseT/UTP <half-duplex>) status: no carrier Starting Network: re2. re2: flags=8802<BROADCAST,SIMPLEX,MULTICAST> metric 0 mtu 1500 options=8209b<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,VLAN_HWCSUM,WOL_MAGIC,LINKSTATE> ether 00:0d:b9:35:88:b6 nd6 options=29<PERFORMNUD,IFDISABLED,AUTO_LINKLOCAL> media: Ethernet autoselect (10baseT/UTP <half-duplex>) status: no carrier add net fe80::: gateway ::1 add net ff02::: gateway ::1 add net ::ffff:0.0.0.0: gateway ::1 add net ::0.0.0.0: gateway ::1 Generating host.conf. eval: cannot create /etc/host.conf: Read-only file system eval: cannot create /etc/host.conf: Read-only file system eval: cannot create /etc/host.conf: Read-only file system Creating and/or trimming log files. Starting syslogd. ELF ldconfig path: /lib /usr/lib /usr/lib/compat 32-bit compatibility ldconfig path: /usr/lib32 Clearing /tmp (X related). Starting local daemons: Welcome to FreeBSD! Please choose the appropriate terminal type for your system. Common console types are: ansi Standard ANSI terminal vt100 VT100 or compatible terminal xterm xterm terminal emulator (or compatible) cons25w cons25w terminal Console type [vt100]:
______ ____ _____ _____ | ____| | _ \ / ____| __ \ | |___ _ __ ___ ___ | |_) | (___ | | | | | ___| '__/ _ \/ _ \| _ < \___ \| | | | | | | | | __/ __/| |_) |____) | |__| | | | | | | | || | | | |_| |_| \___|\___||____/|_____/|_____/ ``` ` s` `.....---.......--.``` -/ +------------Welcome to FreeBSD-----------+ +o .--` /y:` +. | | yo`:. : `+- | 1. Boot Multi User [Enter] | y/ -/` -o/ | 2. Boot [S]ingle User | .- ::/sy+:. | 3. [Esc]ape to loader prompt | / `-- / | 4. Reboot | `: :` | | `: :` | Options: | / / | 5. Configure Boot [O]ptions... | .- -. | | -- -. | | `:` `:` | | .-- `--. | | .---.....----. +-----------------------------------------+ Booting... Copyright (c) 1992-2014 The FreeBSD Project. Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 The Regents of the University of California. All rights reserved. FreeBSD is a registered trademark of The FreeBSD Foundation. FreeBSD 10.0-RELEASE #0 r260789: Thu Jan 16 22:34:59 UTC 2014 root@snap.freebsd.org:/usr/obj/usr/src/sys/GENERIC amd64 FreeBSD clang version 3.3 (tags/RELEASE_33/final 183502) 20130610 CPU: AMD G-T40E Processor (1000.02-MHz K8-class CPU) Origin = "AuthenticAMD" Id = 0x500f20 Family = 0x14 Model = 0x2 Stepping = 0 Features=0x178bfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,MMX,FXSR,SSE,SSE2,HTT> Features2=0x802209<SSE3,MON,SSSE3,CX16,POPCNT> AMD Features=0x2e500800<SYSCALL,NX,MMX+,FFXSR,Page1GB,RDTSCP,LM> AMD Features2=0x35ff<LAHF,CMP,SVM,ExtAPIC,CR8,ABM,SSE4A,MAS,Prefetch,IBS,SKINIT,WDT> TSC: P-state invariant, performance statistics real memory = 4815060992 (4592 MB) avail memory = 4087537664 (3898 MB) Event timer "LAPIC" quality 400 ACPI APIC Table: <CORE COREBOOT> FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs FreeBSD/SMP: 1 package(s) x 2 core(s) cpu0 (BSP): APIC ID: 0 cpu1 (AP): APIC ID: 1 random device not loaded; using insecure entropy ioapic0 <Version 2.1> irqs 0-23 on motherboard kbd0 at kbdmux0 random: <Software, Yarrow> initialized module_register_init: MOD_LOAD (vesa, 0xffffffff80cfa5e0, 0) error 19 acpi0: <CORE COREBOOT> on motherboard acpi0: Power Button (fixed) cpu0: <ACPI CPU> on acpi0 cpu1: <ACPI CPU> on acpi0 atrtc0: <AT realtime clock> port 0x70-0x71 irq 8 on acpi0 Event timer "RTC" frequency 32768 Hz quality 0 attimer0: <AT timer> port 0x40-0x43 irq 0 on acpi0 Timecounter "i8254" frequency 1193182 Hz quality 0 Event timer "i8254" frequency 1193182 Hz quality 100 Timecounter "ACPI-fast" frequency 3579545 Hz quality 900 acpi_timer0: <32-bit timer at 3.579545MHz> port 0x808-0x80b on acpi0 hpet0: <High Precision Event Timer> iomem 0xfed00000-0xfed003ff on acpi0 Timecounter "HPET" frequency 14318180 Hz quality 950 Event timer "HPET" frequency 14318180 Hz quality 550 Event timer "HPET1" frequency 14318180 Hz quality 450 pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff iomem 0xa0000-0xbffff on acpi0 pci0: <ACPI PCI bus> on pcib0 pcib1: <ACPI PCI-PCI bridge> irq 16 at device 4.0 on pci0 pci1: <ACPI PCI bus> on pcib1 re0: <RealTek 8168/8111 B/C/CP/D/DP/E/F/G PCIe Gigabit Ethernet> port 0x1000-0x10ff mem 0xf7900000-0xf7900fff,0xf7800000-0xf7803fff irq 16 at device 0.0 on pci1 re0: Using 1 MSI-X message re0: ASPM disabled re0: Chip rev. 0x2c000000 re0: MAC rev. 0x00200000 miibus0: <MII bus> on re0 rgephy0: <RTL8169S/8110S/8211 1000BASE-T media interface> PHY 1 on miibus0 rgephy0: none, 10baseT, 10baseT-FDX, 10baseT-FDX-flow, 100baseTX, 100baseTX-FDX, 100baseTX-FDX-flow, 1000baseT, 1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, 1000baseT-FDX-flow, 1000baseT-FDX-flow-master, auto, auto-flow re0: Ethernet address: 00:0d:b9:35:88:b4 pcib2: <ACPI PCI-PCI bridge> irq 17 at device 5.0 on pci0 pci2: <ACPI PCI bus> on pcib2 re1: <RealTek 8168/8111 B/C/CP/D/DP/E/F/G PCIe Gigabit Ethernet> port 0x2000-0x20ff mem 0xf7b00000-0xf7b00fff,0xf7a00000-0xf7a03fff irq 17 at device 0.0 on pci2 re1: Using 1 MSI-X message re1: ASPM disabled re1: Chip rev. 0x2c000000 re1: MAC rev. 0x00200000 miibus1: <MII bus> on re1 rgephy1: <RTL8169S/8110S/8211 1000BASE-T media interface> PHY 1 on miibus1 rgephy1: none, 10baseT, 10baseT-FDX, 10baseT-FDX-flow, 100baseTX, 100baseTX-FDX, 100baseTX-FDX-flow, 1000baseT, 1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, 1000baseT-FDX-flow, 1000baseT-FDX-flow-master, auto, auto-flow re1: Ethernet address: 00:0d:b9:35:88:b5 pcib3: <ACPI PCI-PCI bridge> irq 18 at device 6.0 on pci0 pci3: <ACPI PCI bus> on pcib3 re2: <RealTek 8168/8111 B/C/CP/D/DP/E/F/G PCIe Gigabit Ethernet> port 0x3000-0x30ff mem 0xf7d00000-0xf7d00fff,0xf7c00000-0xf7c03fff irq 18 at device 0.0 on pci3 re2: Using 1 MSI-X message re2: ASPM disabled re2: Chip rev. 0x2c000000 re2: MAC rev. 0x00200000 miibus2: <MII bus> on re2 rgephy2: <RTL8169S/8110S/8211 1000BASE-T media interface> PHY 1 on miibus2 rgephy2: none, 10baseT, 10baseT-FDX, 10baseT-FDX-flow, 100baseTX, 100baseTX-FDX, 100baseTX-FDX-flow, 1000baseT, 1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, 1000baseT-FDX-flow, 1000baseT-FDX-flow-master, auto, auto-flow re2: Ethernet address: 00:0d:b9:35:88:b6 pcib4: <ACPI PCI-PCI bridge> irq 19 at device 7.0 on pci0 pci4: <ACPI PCI bus> on pcib4 ath0: <Atheros 9280> at device 0.0 on pci4 [ath] enabling AN_TOP2_FIXUP ath0: [HT] enabling HT modes ath0: [HT] 1 stream STBC receive enabled ath0: [HT] 1 stream STBC transmit enabled ath0: [HT] 2 RX streams; 2 TX streams ath0: AR9280 mac 128.2 RF5133 phy 13.0 ath0: 2GHz radio: 0x0000; 5GHz radio: 0x00c0 ahci0: <ATI IXP700 AHCI SATA controller> port 0x4010-0x4017,0x4020-0x4023,0x4018-0x401f,0x4024-0x4027,0x4000-0x400f mem 0xf7f04000-0xf7f043ff irq 19 at device 17.0 on pci0 ahci0: AHCI v1.20 with 6 6Gbps ports, Port Multiplier supported ahcich0: <AHCI channel> at channel 0 on ahci0 ahcich1: <AHCI channel> at channel 1 on ahci0 ahcich2: <AHCI channel> at channel 2 on ahci0 ahcich3: <AHCI channel> at channel 3 on ahci0 ahcich4: <AHCI channel> at channel 4 on ahci0 ahcich5: <AHCI channel> at channel 5 on ahci0 ohci0: <AMD SB7x0/SB8x0/SB9x0 USB controller> mem 0xf7f00000-0xf7f00fff irq 18 at device 18.0 on pci0 usbus0 on ohci0 ehci0: <AMD SB7x0/SB8x0/SB9x0 USB 2.0 controller> mem 0xf7f04400-0xf7f044ff irq 17 at device 18.2 on pci0 usbus1: EHCI version 1.0 usbus1 on ehci0 ohci1: <AMD SB7x0/SB8x0/SB9x0 USB controller> mem 0xf7f01000-0xf7f01fff irq 18 at device 19.0 on pci0 usbus2 on ohci1 ehci1: <AMD SB7x0/SB8x0/SB9x0 USB 2.0 controller> mem 0xf7f04500-0xf7f045ff irq 17 at device 19.2 on pci0 usbus3: EHCI version 1.0 usbus3 on ehci1 pci0: <serial bus, SMBus> at device 20.0 (no driver attached) isab0: <PCI-ISA bridge> at device 20.3 on pci0 isa0: <ISA bus> on isab0 pcib5: <ACPI PCI-PCI bridge> at device 20.4 on pci0 pci5: <ACPI PCI bus> on pcib5 ohci2: <AMD SB7x0/SB8x0/SB9x0 USB controller> mem 0xf7f02000-0xf7f02fff irq 18 at device 20.5 on pci0 usbus4 on ohci2 pcib6: <ACPI PCI-PCI bridge> at device 21.0 on pci0 pci6: <ACPI PCI bus> on pcib6 ohci3: <AMD SB7x0/SB8x0/SB9x0 USB controller> mem 0xf7f03000-0xf7f03fff at device 22.0 on pci0 usbus5 on ohci3 ehci2: <AMD SB7x0/SB8x0/SB9x0 USB 2.0 controller> mem 0xf7f04600-0xf7f046ff at device 22.2 on pci0 usbus6: EHCI version 1.0 usbus6 on ehci2 amdtemp0: <AMD CPU On-Die Thermal Sensors> on hostb4 acpi_button0: <Power Button> on acpi0 orm0: <ISA Option ROM> at iomem 0xee800-0xeffff on isa0 ppc0: cannot reserve I/O port range uart0: <16550 or compatible> at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0 uart0: console (9600,n,8,1) uart1: <16550 or compatible> at port 0x2f8-0x2ff irq 3 on isa0 acpi_throttle0: <ACPI CPU Throttling> on cpu0 acpi_throttle1: <ACPI CPU Throttling> on cpu1 acpi_throttle1: failed to attach P_CNT device_attach: acpi_throttle1 attach returned 6 Timecounters tick every 1.000 msec random: unblocking device. usbus0: 12Mbps Full Speed USB v1.0 usbus1: 480Mbps High Speed USB v2.0 ugen0.1: <ATI> at usbus0 uhub0: <ATI OHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus0 ugen1.1: <ATI> at usbus1 uhub1: <ATI EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus1 usbus2: 12Mbps Full Speed USB v1.0 usbus3: 480Mbps High Speed USB v2.0 ugen2.1: <ATI> at usbus2 uhub2: <ATI OHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus2 ugen3.1: <ATI> at usbus3 uhub3: <ATI EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus3 usbus4: 12Mbps Full Speed USB v1.0 usbus5: 12Mbps Full Speed USB v1.0 ugen4.1: <ATI> at usbus4 uhub4: <ATI OHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus4 ugen5.1: <ATI> at usbus5 uhub5: <ATI OHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus5 usbus6: 480Mbps High Speed USB v2.0 uhub0: 5 ports with 5 removable, self powered ugen6.1: <ATI> at usbus6 uhub6: <ATI EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus6 uhub4: 2 ports with 2 removable, self powered uhub2: 5 ports with 5 removable, self powered ada0 at ahcich0 bus 0 scbus0 target 0 lun 0 ada0: <SB mSATA SSD S9FM01.8> ATA-10uhub5: 4 ports with 4 removable, self powered SATA 3.x device ada0: Serial Number DDDF074704EE00609569 ada0: 600.000MB/s transfers (SATA 3.x, UDMA6, PIO 8192bytes) ada0: Command Queueing enabled ada0: 14318MB (29323728 512 byte sectors: 16H 63S/T 16383C) ada0: Previously was known as ad4 Netvsc initializing... SMP: AP CPU #1 Launched! Timecounter "TSC" frequency 1000022033 Hz quality 800 Root mount waiting for: usbus6 usbus3 usbus1 uhub1: 5 ports with 5 removable, self powered uhub6: 4 ports with 4 removable, self powered uhub3: 5 ports with 5 removable, self powered Root mount waiting for: usbus6 ugen6.2: <Generic> at usbus6 umass0: <Generic Flash Card ReaderWriter, class 0/0, rev 2.01/1.00, addr 2> on usbus6 umass0: SCSI over Bulk-Only; quirks = 0x4001 Root mount waiting for: usbus6 umass0:6:0:-1: Attached to scbus6 da0 at umass-sim0 bus 0 scbus6 target 0 lun 0 da0: <Multiple Card Reader 1.00> Removable Direct Access SCSI-4 device da0: Serial Number 058F63666485 da0: 40.000MB/s transfers da0: Attempt to query device size failed: NOT READY, Medium not present da0: quirks=0x2<NO_6_BYTE> Trying to mount root from ufs:/dev/ada0p2 [rw]... Setting hostuuid: 2b9c83ad-c7a3-11e3-9908-000db93588b4. Setting hostid: 0xa64d7547. Entropy harvesting: interrupts ethernet point_to_point swi. Starting file system checks: /dev/ada0p2: FILE SYSTEM CLEAN; SKIPPING CHECKS /dev/ada0p2: clean, 2655278 free (598 frags, 331835 blocks, 0.0% fragmentation) Mounting local file systems:. Writing entropy file:. Setting hostname: gateway. re0: link state changed to DOWN Starting Networkre0: link state changed to UP : lo0 re0 re1 rere1: link state changed to DOWN 2. lo0: flags=8re2: link state changed to DOWN 049<UP,LOOPBACK,RUNNING,MULTICAST> metric 0 mtu 16384 options=600003<RXCSUM,TXCSUM,RXCSUM_IPV6,TXCSUM_IPV6> inet6 ::1 prefixlen 128 inet6 fe80::1%lo0 prefixlen 64 scopeid 0x5 inet 127.0.0.1 netmask 0xff000000 nd6 options=21<PERFORMNUD,AUTO_LINKLOCAL> re0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 1500 options=8209b<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,VLAN_HWCSUM,WOL_MAGIC,LINKSTATE> ether 00:0d:b9:35:88:b4 inet 10.41.10.1 netmask 0xffff0000 broadcast 10.41.255.255 inet6 fe80::20d:b9ff:fe35:88b4%re0 prefixlen 64 scopeid 0x1 nd6 options=29<PERFORMNUD,IFDISABLED,AUTO_LINKLOCAL> media: Ethernet autoselect (1000baseT <full-duplex>) status: active re1: flags=8802<BROADCAST,SIMPLEX,MULTICAST> metric 0 mtu 1500 options=8209b<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,VLAN_HWCSUM,WOL_MAGIC,LINKSTATE> ether 00:0d:b9:35:88:b5 nd6 options=29<PERFORMNUD,IFDISABLED,AUTO_LINKLOCAL> media: Ethernet autoselect (10baseT/UTP <half-duplex>) status: no carrier re2: flags=8802<BROADCAST,SIMPLEX,MULTICAST> metric 0 mtu 1500 options=8209b<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,VLAN_HWCSUM,WOL_MAGIC,LINKSTATE> ether 00:0d:b9:35:88:b6 nd6 options=29<PERFORMNUD,IFDISABLED,AUTO_LINKLOCAL> media: Ethernet autoselect (10baseT/UTP <half-duplex>) status: no carrier Starting devd. Starting Network: re1. re1: flags=8802<BROADCAST,SIMPLEX,MULTICAST> metric 0 mtu 1500 options=8209b<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,VLAN_HWCSUM,WOL_MAGIC,LINKSTATE> ether 00:0d:b9:35:88:b5 nd6 options=29<PERFORMNUD,IFDISABLED,AUTO_LINKLOCAL> media: Ethernet autoselect (10baseT/UTP <half-duplex>) status: no carrier Starting Network: re2. re2: flags=8802<BROADCAST,SIMPLEX,MULTICAST> metric 0 mtu 1500 options=8209b<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,VLAN_HWCSUM,WOL_MAGIC,LINKSTATE> ether 00:0d:b9:35:88:b6 nd6 options=29<PERFORMNUD,IFDISABLED,AUTO_LINKLOCAL> media: Ethernet autoselect (10baseT/UTP <half-duplex>) status: no carrier add net default: gateway 10.41.0.2 add net fe80::: gateway ::1 add net ff02::: gateway ::1 add net ::ffff:0.0.0.0: gateway ::1 add net ::0.0.0.0: gateway ::1 Creating and/or trimming log files. Starting syslogd. No core dumps found. ELF ldconfig path: /lib /usr/lib /usr/lib/compat 32-bit compatibility ldconfig path: /usr/lib32 Clearing /tmp (X related). Updating motd:. Mounting late file systems:. Performing sanity check on sshd configuration. Starting sshd. Starting sendmail_submit. Starting sendmail_msp_queue. Starting cron. Starting background file system checks in 60 seconds. Sat Apr 19 12:39:53 CEST 2014 FreeBSD/amd64 (gateway) (ttyu0) login:
Waiting (max 60 seconds) for system process `vnlru' to stop...done Waiting (max 60 seconds) for system process `bufdaemon' to stop...done Waiting (max 60 seconds) for system process `syncer' to stop... Syncing disks, vnodes remaining...2 1 0 done All buffers synced. Uptime: 30m29s re0: link state changed to DOWN re0: link state changed to UP usbus0: Controller shutdown uhub0: at usbus0, port 1, addr 1 (disconnected) usbus0: Controller shutdown complete usbus1: Controller shutdown uhub1: at usbus1, port 1, addr 1 (disconnected) usbus1: Controller shutdown complete usbus2: Controller shutdown uhub2: at usbus2, port 1, addr 1 (disconnected) usbus2: Controller shutdown complete usbus3: Controller shutdown uhub3: at usbus3, port 1, addr 1 (disconnected) usbus3: Controller shutdown complete usbus4: Controller shutdown uhub4: at usbus4, port 1, addr 1 (disconnected) usbus4: Controller shutdown complete usbus5: Controller shutdown uhub5: at usbus5, port 1, addr 1 (disconnected) usbus5: Controller shutdown complete usbus6: Controller shutdown uhub6: at usbus6, port 1, addr 1 (disconnected) ugen6.2: <Generic> at usbus6 (disconnected) umass0: at uhub6, port 1, addr 2 (disconnected) da0 at umass-sim0 bus 0 scbus6 target 0 lun 0 da0: <Multiple Card Reader 1.00> s/n 058F63666485 detached (da0:umass-sim0:0:0:0): Periph destroyed usbus6: Controller shutdown complete acpi0: Powering system off
# cat /etc/fstab # Device Mountpoint FStype Options Dump Pass# /dev/ada0p2 / ufs rw 1 1 /dev/ada0p3 none swap sw 0 0 # gpart show => 34 29323661 ada0 GPT (14G) 34 128 1 freebsd-boot (64K) 162 27262848 2 freebsd-ufs (13G) 27263010 1466368 3 freebsd-swap (716M) 28729378 594317 - free - (290M)
Old: # tunefs -p /dev/ada0p2 tunefs: POSIX.1e ACLs: (-a) disabled tunefs: NFSv4 ACLs: (-N) disabled tunefs: MAC multilabel: (-l) disabled tunefs: soft updates: (-n) enabled tunefs: soft update journaling: (-j) enabled tunefs: gjournal: (-J) disabled tunefs: trim: (-t) disabled tunefs: maximum blocks per file in a cylinder group: (-e) 4096 tunefs: average file size: (-f) 16384 tunefs: average number of files in a directory: (-s) 64 tunefs: minimum percentage of free space: (-m) 8% tunefs: space to hold for metadata blocks: (-k) 6408 tunefs: optimization preference: (-o) time tunefs: volume label: (-L) New: # tunefs -t enable /dev/ada0p2 tunefs: issue TRIM to the disk set # tunefs -j disable /dev/ada0p2 Clearing journal flags from inode 4 tunefs: soft updates journaling cleared but soft updates still set. tunefs: remove .sujournal to reclaim space # tunefs -p /dev/ada0p2 tunefs: POSIX.1e ACLs: (-a) disabled tunefs: NFSv4 ACLs: (-N) disabled tunefs: MAC multilabel: (-l) disabled tunefs: soft updates: (-n) enabled tunefs: soft update journaling: (-j) disabled tunefs: gjournal: (-J) disabled tunefs: trim: (-t) enabled tunefs: maximum blocks per file in a cylinder group: (-e) 4096 tunefs: average file size: (-f) 16384 tunefs: average number of files in a directory: (-s) 64 tunefs: minimum percentage of free space: (-m) 8% tunefs: space to hold for metadata blocks: (-k) 6408 tunefs: optimization preference: (-o) time tunefs: volume label: (-L)
# sysctl dev.cpu dev.cpu.0.%desc: ACPI CPU dev.cpu.0.%driver: cpu dev.cpu.0.%location: handle=\_PR_.C000 dev.cpu.0.%pnpinfo: _HID=none _UID=0 dev.cpu.0.%parent: acpi0 dev.cpu.0.freq: 1000 dev.cpu.0.freq_levels: 1000/-1 875/-1 750/-1 625/-1 500/-1 375/-1 250/-1 125/-1 dev.cpu.0.cx_supported: C1/1/0 C2/2/100 dev.cpu.0.cx_lowest: C1 dev.cpu.0.cx_usage: 100.00% 0.00% last 30635us dev.cpu.0.temperature: 53.0C dev.cpu.1.%desc: ACPI CPU dev.cpu.1.%driver: cpu dev.cpu.1.%location: handle=\_PR_.C001 dev.cpu.1.%pnpinfo: _HID=none _UID=0 dev.cpu.1.%parent: acpi0 dev.cpu.1.cx_supported: C1/1/0 dev.cpu.1.cx_lowest: C1 dev.cpu.1.cx_usage: 100.00% last 10638us dev.cpu.1.temperature: 53.0C
Temperature
How can I monitor CPU temperature and fan speed?
Monitoring the CPU temperature of your FreeBSD system in Zabbix
Get temperature of CPU (Intel Core i5) in FreeBSD
# kldload amdtemp amdtemp0: <AMD CPU On-Die Thermal Sensors> on hostb4 # sysctl dev.cpu | grep temp dev.cpu.0.temperature: 53.0C dev.cpu.1.temperature: 53.0C
# dmesg | grep Timecounter Timecounter "i8254" frequency 1193182 Hz quality 0 Timecounter "ACPI-fast" frequency 3579545 Hz quality 900 Timecounter "HPET" frequency 14318180 Hz quality 950 Timecounters tick every 1.000 msec Timecounter "TSC" frequency 1000019630 Hz quality 800
Booting... Copyright (c) 1992-2014 The FreeBSD Project. Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 The Regents of the University of California. All rights reserved. FreeBSD is a registered trademark of The FreeBSD Foundation. FreeBSD 10.0-RELEASE #0 r260789: Thu Jan 16 22:34:59 UTC 2014 root@snap.freebsd.org:/usr/obj/usr/src/sys/GENERIC amd64 FreeBSD clang version 3.3 (tags/RELEASE_33/final 183502) 20130610 CPU: AMD G-T40E Processor (1000.02-MHz K8-class CPU) Origin = "AuthenticAMD" Id = 0x500f20 Family = 0x14 Model = 0x2 Stepping = 0 Features=0x178bfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,MMX,FXSR,SSE,SSE2,HTT> Features2=0x802209<SSE3,MON,SSSE3,CX16,POPCNT> AMD Features=0x2e500800<SYSCALL,NX,MMX+,FFXSR,Page1GB,RDTSCP,LM> AMD Features2=0x35ff<LAHF,CMP,SVM,ExtAPIC,CR8,ABM,SSE4A,MAS,Prefetch,IBS,SKINIT,WDT> TSC: P-state invariant, performance statistics real memory = 4815060992 (4592 MB) avail memory = 4087537664 (3898 MB) Event timer "LAPIC" quality 400 ACPI APIC Table: <CORE COREBOOT> FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs FreeBSD/SMP: 1 package(s) x 2 core(s) cpu0 (BSP): APIC ID: 0 cpu1 (AP): APIC ID: 1 random device not loaded; using insecure entropy ioapic0 <Version 2.1> irqs 0-23 on motherboard kbd0 at kbdmux0 random: <Software, Yarrow> initialized module_register_init: MOD_LOAD (vesa, 0xffffffff80cfa5e0, 0) error 19 acpi0: <CORE COREBOOT> on motherboard acpi0: Power Button (fixed) cpu0: <ACPI CPU> on acpi0 cpu1: <ACPI CPU> on acpi0 atrtc0: <AT realtime clock> port 0x70-0x71 irq 8 on acpi0 Event timer "RTC" frequency 32768 Hz quality 0 attimer0: <AT timer> port 0x40-0x43 irq 0 on acpi0 Timecounter "i8254" frequency 1193182 Hz quality 0 Event timer "i8254" frequency 1193182 Hz quality 100 Timecounter "ACPI-fast" frequency 3579545 Hz quality 900 acpi_timer0: <32-bit timer at 3.579545MHz> port 0x808-0x80b on acpi0 hpet0: <High Precision Event Timer> iomem 0xfed00000-0xfed003ff on acpi0 Timecounter "HPET" frequency 14318180 Hz quality 950 Event timer "HPET" frequency 14318180 Hz quality 550 Event timer "HPET1" frequency 14318180 Hz quality 450 pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff iomem 0xa0000-0xbffff on acpi0 pci0: <ACPI PCI bus> on pcib0 pcib1: <ACPI PCI-PCI bridge> irq 16 at device 4.0 on pci0 pci1: <ACPI PCI bus> on pcib1 re0: <RealTek 8168/8111 B/C/CP/D/DP/E/F/G PCIe Gigabit Ethernet> port 0x1000-0x10ff mem 0xf7900000-0xf7900fff,0xf7800000-0xf7803fff irq 16 at device 0.0 on pci1 re0: Using 1 MSI-X message re0: ASPM disabled re0: Chip rev. 0x2c000000 re0: MAC rev. 0x00200000 miibus0: <MII bus> on re0 rgephy0: <RTL8169S/8110S/8211 1000BASE-T media interface> PHY 1 on miibus0 rgephy0: none, 10baseT, 10baseT-FDX, 10baseT-FDX-flow, 100baseTX, 100baseTX-FDX, 100baseTX-FDX-flow, 1000baseT, 1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, 1000baseT-FDX-flow, 1000baseT-FDX-flow-master, auto, auto-flow re0: Ethernet address: 00:0d:b9:35:88:b4 pcib2: <ACPI PCI-PCI bridge> irq 17 at device 5.0 on pci0 pci2: <ACPI PCI bus> on pcib2 re1: <RealTek 8168/8111 B/C/CP/D/DP/E/F/G PCIe Gigabit Ethernet> port 0x2000-0x20ff mem 0xf7b00000-0xf7b00fff,0xf7a00000-0xf7a03fff irq 17 at device 0.0 on pci2 re1: Using 1 MSI-X message re1: ASPM disabled re1: Chip rev. 0x2c000000 re1: MAC rev. 0x00200000 miibus1: <MII bus> on re1 rgephy1: <RTL8169S/8110S/8211 1000BASE-T media interface> PHY 1 on miibus1 rgephy1: none, 10baseT, 10baseT-FDX, 10baseT-FDX-flow, 100baseTX, 100baseTX-FDX, 100baseTX-FDX-flow, 1000baseT, 1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, 1000baseT-FDX-flow, 1000baseT-FDX-flow-master, auto, auto-flow re1: Ethernet address: 00:0d:b9:35:88:b5 pcib3: <ACPI PCI-PCI bridge> irq 18 at device 6.0 on pci0 pci3: <ACPI PCI bus> on pcib3 re2: <RealTek 8168/8111 B/C/CP/D/DP/E/F/G PCIe Gigabit Ethernet> port 0x3000-0x30ff mem 0xf7d00000-0xf7d00fff,0xf7c00000-0xf7c03fff irq 18 at device 0.0 on pci3 re2: Using 1 MSI-X message re2: ASPM disabled re2: Chip rev. 0x2c000000 re2: MAC rev. 0x00200000 miibus2: <MII bus> on re2 rgephy2: <RTL8169S/8110S/8211 1000BASE-T media interface> PHY 1 on miibus2 rgephy2: none, 10baseT, 10baseT-FDX, 10baseT-FDX-flow, 100baseTX, 100baseTX-FDX, 100baseTX-FDX-flow, 1000baseT, 1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, 1000baseT-FDX-flow, 1000baseT-FDX-flow-master, auto, auto-flow re2: Ethernet address: 00:0d:b9:35:88:b6 pcib4: <ACPI PCI-PCI bridge> irq 19 at device 7.0 on pci0 pci4: <ACPI PCI bus> on pcib4 ath0: <Atheros 9280> at device 0.0 on pci4 [ath] enabling AN_TOP2_FIXUP ath0: [HT] enabling HT modes ath0: [HT] 1 stream STBC receive enabled ath0: [HT] 1 stream STBC transmit enabled ath0: [HT] 2 RX streams; 2 TX streams ath0: AR9280 mac 128.2 RF5133 phy 13.0 ath0: 2GHz radio: 0x0000; 5GHz radio: 0x00c0 ahci0: <ATI IXP700 AHCI SATA controller> port 0x4010-0x4017,0x4020-0x4023,0x4018-0x401f,0x4024-0x4027,0x4000-0x400f mem 0xf7f04000-0xf7f043ff irq 19 at device 17.0 on pci0 ahci0: AHCI v1.20 with 6 6Gbps ports, Port Multiplier supported ahcich0: <AHCI channel> at channel 0 on ahci0 ahcich1: <AHCI channel> at channel 1 on ahci0 ahcich2: <AHCI channel> at channel 2 on ahci0 ahcich3: <AHCI channel> at channel 3 on ahci0 ahcich4: <AHCI channel> at channel 4 on ahci0 ahcich5: <AHCI channel> at channel 5 on ahci0 ohci0: <AMD SB7x0/SB8x0/SB9x0 USB controller> mem 0xf7f00000-0xf7f00fff irq 18 at device 18.0 on pci0 usbus0 on ohci0 ehci0: <AMD SB7x0/SB8x0/SB9x0 USB 2.0 controller> mem 0xf7f04400-0xf7f044ff irq 17 at device 18.2 on pci0 usbus1: EHCI version 1.0 usbus1 on ehci0 ohci1: <AMD SB7x0/SB8x0/SB9x0 USB controller> mem 0xf7f01000-0xf7f01fff irq 18 at device 19.0 on pci0 usbus2 on ohci1 ehci1: <AMD SB7x0/SB8x0/SB9x0 USB 2.0 controller> mem 0xf7f04500-0xf7f045ff irq 17 at device 19.2 on pci0 usbus3: EHCI version 1.0 usbus3 on ehci1 pci0: <serial bus, SMBus> at device 20.0 (no driver attached) isab0: <PCI-ISA bridge> at device 20.3 on pci0 isa0: <ISA bus> on isab0 pcib5: <ACPI PCI-PCI bridge> at device 20.4 on pci0 pci5: <ACPI PCI bus> on pcib5 ohci2: <AMD SB7x0/SB8x0/SB9x0 USB controller> mem 0xf7f02000-0xf7f02fff irq 18 at device 20.5 on pci0 usbus4 on ohci2 pcib6: <ACPI PCI-PCI bridge> at device 21.0 on pci0 pci6: <ACPI PCI bus> on pcib6 ohci3: <AMD SB7x0/SB8x0/SB9x0 USB controller> mem 0xf7f03000-0xf7f03fff at device 22.0 on pci0 usbus5 on ohci3 ehci2: <AMD SB7x0/SB8x0/SB9x0 USB 2.0 controller> mem 0xf7f04600-0xf7f046ff at device 22.2 on pci0 usbus6: EHCI version 1.0 usbus6 on ehci2 amdtemp0: <AMD CPU On-Die Thermal Sensors> on hostb4 acpi_button0: <Power Button> on acpi0 orm0: <ISA Option ROM> at iomem 0xee800-0xeffff on isa0 ppc0: cannot reserve I/O port range uart0: <16550 or compatible> at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0 uart0: console (9600,n,8,1) uart1: <16550 or compatible> at port 0x2f8-0x2ff irq 3 on isa0 acpi_throttle0: <ACPI CPU Throttling> on cpu0 acpi_throttle1: <ACPI CPU Throttling> on cpu1 acpi_throttle1: failed to attach P_CNT device_attach: acpi_throttle1 attach returned 6 Timecounters tick every 1.000 msec random: unblocking device. usbus0: 12Mbps Full Speed USB v1.0 usbus1: 480Mbps High Speed USB v2.0 ugen0.1: <ATI> at usbus0 uhub0: <ATI OHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus0 ugen1.1: <ATI> at usbus1 uhub1: <ATI EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus1 usbus2: 12Mbps Full Speed USB v1.0 usbus3: 480Mbps High Speed USB v2.0 ugen2.1: <ATI> at usbus2 uhub2: <ATI OHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus2 ugen3.1: <ATI> at usbus3 uhub3: <ATI EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus3 usbus4: 12Mbps Full Speed USB v1.0 usbus5: 12Mbps Full Speed USB v1.0 ugen4.1: <ATI> at usbus4 uhub4: <ATI OHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus4 ugen5.1: <ATI> at usbus5 uhub5: <ATI OHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus5 usbus6: 480Mbps High Speed USB v2.0 uhub0: 5 ports with 5 removable, self powered ugen6.1: <ATI> at usbus6 uhub6: <ATI EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus6 uhub4: 2 ports with 2 removable, self powered uhub2: 5 ports with 5 removable, self powered ada0 at ahcich0 bus 0 scbus0 target 0 lun 0 ada0: <SB mSATA SSD S9FM01.8> ATA-10uhub5: 4 ports with 4 removable, self powered SATA 3.x device ada0: Serial Number DDDF074704EE00609569 ada0: 600.000MB/s transfers (SATA 3.x, UDMA6, PIO 8192bytes) ada0: Command Queueing enabled ada0: 14318MB (29323728 512 byte sectors: 16H 63S/T 16383C) ada0: Previously was known as ad4 Netvsc initializing... SMP: AP CPU #1 Launched! Timecounter "TSC" frequency 1000021653 Hz quality 800 Root mount waiting for: usbus6 usbus3 usbus1 uhub1: 5 ports with 5 removable, self powered uhub3: 5 ports with 5 removable, self powered uhub6: 4 ports with 4 removable, self powered Root mount waiting for: usbus6 ugen6.2: <Generic> at usbus6 umass0: <Generic Flash Card ReaderWriter, class 0/0, rev 2.01/1.00, addr 2> on usbus6 umass0: SCSI over Bulk-Only; quirks = 0x4001 Root mount waiting for: usbus6 umass0:6:0:-1: Attached to scbus6 da0 at umass-sim0 bus 0 scbus6 target 0 lun 0 da0: <Multiple Card Reader 1.00> Removable Direct Access SCSI-4 device da0: Serial Number 058F63666485 da0: 40.000MB/s transfers da0: Attempt to query device size failed: NOT READY, Medium not present da0: quirks=0x2<NO_6_BYTE> Trying to mount root from ufs:/dev/ada0p2 [rw]... Setting hostuuid: 2b9c83ad-c7a3-11e3-9908-000db93588b4. Setting hostid: 0xa64d7547. Entropy harvesting: interrupts ethernet point_to_point swi. Starting file system checks: /dev/ada0p2: FILE SYSTEM CLEAN; SKIPPING CHECKS /dev/ada0p2: clean, 2623721 free (721 frags, 327875 blocks, 0.0% fragmentation) Mounting local file systems:. Writing entropy file:. Setting hostname: gateway.ines.zhaw.ch. re0: link state changed to DOWN wlan0: Ethernet address: 04:f0:21:0c:2b:a6 Fatal trap 12: page fault while in kernel mode cpuid = 1; apic id = 01 fault virtual address = 0x0 fault code = supervisor read instruction, page not present instruction pointer = 0x20:0x0 stack pointer = 0x28:0xfffffe01213eab20 frame pointer = 0x28:0xfffffe01213eab80 code segment = base 0x0, limit 0xfffff, type 0x1b = DPL 0, pres 1, long 1, def32 0, gran 1 processor eflags = interrupt enabled, resume, IOPL = 0 current process = 0 (ath0 net80211 taskq) trap number = 12 panic: page fault cpuid = 1 KDB: stack backtrace: #0 0xffffffff808e7dd0 at kdb_backtrace+0x60 #1 0xffffffff808af8b5 at panic+0x155 #2 0xffffffff80c8e692 at trap_fatal+0x3a2 #3 0xffffffff80c8e969 at trap_pfault+0x2c9 #4 0xffffffff80c8e0f6 at trap+0x5e6 #5 0xffffffff80c75392 at calltrap+0x8 #6 0xffffffff808f63e8 at taskqueue_thread_loop+0xa8 #7 0xffffffff8088198a at fork_exit+0x9a #8 0xffffffff80c758ce at fork_trampoline+0xe Uptime: 8s Dumping 273 out of 4042 MB:..6%..12%..24%..36%..41%..53%..65%..71%..82%..94% Dump complete
Configuration
### CONSOLE #################################################################### font8x14="NO" font8x16="swiss-8x16" font8x8="swiss-8x8" keymap="swissgerman.cp850.kbd" ### NETWORK #################################################################### hostname="gateway.ines.zhaw.ch" gateway_enable="YES" # Cable ifconfig_re0="DHCP" # WiFi wlans_ath0="wlan0" create_args_wlan0="wlanmode hostap" ifconfig_wlan0="inet 192.168.0.1 netmask 255.255.255.0 ssid BACHI.NET mode 11ng channel 1 country CH" ### FIREWALL ################################################################### pf_enable="YES" pf_rules="/etc/pf.conf" pf_flags="" pflog_enable="YES" pflog_logfile="/var/log/pf.log" pflog_flags="" ### DAEMONS #################################################################### # Don't start inetd_enable="NO" sendmail_enable="NONE" #NTP ntpd_enable="YES" # SSH sshd_enable="YES" # Host Access Point hostapd_enable="YES" # DHCP dhcpd_enable="YES" dhcpd_ifaces="wlan0" # NFS rpcbind_enable="YES" nfs_server_enable="YES" mountd_enable="YES" mountd_flags="-r" rpc_statd_enable="YES" rpc_lockd_enable="YES" # Set dumpdev to "AUTO" to enable crash dumps, "NO" to disable dumpdev="AUTO"
CPUTYPE?= k8-sse3 BOOTWAIT= 3 NO_MODULES= true
if_inet="re0" # Internet if_lan="wlan0" # Intranet net_lan="192.168.0.0/16" table <hacker> persist { } nat on $if_inet from $net_lan to any -> ($if_inet) block all pass in on $if_inet all pass in on $if_lan all pass out all
interface=wlan0 debug=1 ctrl_interface=/var/run/hostapd ctrl_interface_group=wheel ssid=BACHI.NET wpa=1 wpa_passphrase=********* wpa_key_mgmt=WPA-PSK wpa_pairwise=CCMP TKIP
# # INES -- InES kernel configuration file for FreeBSD/amd64 # cpu HAMMER ident INES options INCLUDE_CONFIG_FILE # Include this file in kernel options PRINTF_BUFR_SIZE=128 # Prevent printf output being interspersed. ############################################################################### # CPU DEVICES AND OPTIONS options SMP # Symmetric MultiProcessor Kernel, SMP-capable kernel by default device cpufreq # CPU frequency control device amdtemp # Thermal sensor for AMD CPU ##################################################################### # PERFORMANCE MONITORING OPTIONS device hwpmc # Hardware Performance Monitoring Counter support options HWPMC_HOOKS # Necessary kernel hooks for hwpmc(4) ############################################################################### # SCHEDULING options SCHED_ULE # ULE scheduler options PREEMPTION # Enable kernel thread preemption options _KPOSIX_PRIORITY_SCHEDULING # POSIX P1003_1B real-time extensions ############################################################################### # FILE SYSTEM options FFS # Berkeley Fast Filesystem options SOFTUPDATES # Enable FFS soft updates support options UFS_ACL # Support for access control lists options UFS_DIRHASH # Improve performance on big directories options UFS_GJOURNAL # Enable gjournal-based UFS journaling options QUOTA # Enable disk quotas for UFS options MD_ROOT # MD is a potential root device options NFSCL # New Network Filesystem Client options NFSD # New Network Filesystem Server options NFSLOCKD # Network Lock Manager options NFS_ROOT # NFS usable as /, requires NFSCL options MSDOSFS # MSDOS Filesystem options CD9660 # ISO 9660 Filesystem options PROCFS # Process filesystem (requires PSEUDOFS) options PSEUDOFS # Pseudo-filesystem framework options NULLFS # Null-filesystem ############################################################################### # GEOM and PARTITIONING options GEOM_PART_GPT # GUID Partition Tables. options GEOM_RAID # Soft RAID functionality. options GEOM_LABEL # Provides labelization ############################################################################### # COMPATIBILITY OPTIONS options COMPAT_FREEBSD32 # Compatible with i386 binaries options COMPAT_FREEBSD4 # Compatible with FreeBSD4 options COMPAT_FREEBSD5 # Compatible with FreeBSD5 options COMPAT_FREEBSD6 # Compatible with FreeBSD6 options COMPAT_FREEBSD7 # Compatible with FreeBSD7 options SYSVSHM # SYSV-style shared memory options SYSVMSG # SYSV-style message queues options SYSVSEM # SYSV-style semaphores ##################################################################### # DEBUGGING OPTIONS makeoptions DEBUG=-g # Build kernel with gdb(1) debug symbols makeoptions WITH_CTF=1 # Run ctfconvert(1) for DTrace support options KDB # Enable kernel debugger support. options KDB_TRACE # Print a stack trace for a panic. options KTRACE # ktrace(1) support, kernel tracing options STACK # stack(9) support, capture of kernel stack for procinfo(1) options KDTRACE_FRAME # Ensure frames are compiled in options KDTRACE_HOOKS # Kernel DTrace hooks options DDB_CTF # Kernel ELF linker loads CTF data ##################################################################### # SECURITY POLICY PARAMETERS options AUDIT # Security event auditing options CAPABILITY_MODE # Capsicum capability mode options CAPABILITIES # Capsicum capabilities options PROCDESC # Support for process descriptors options MAC # TrustedBSD MAC Framework ############################################################################### # BUS SUPPORT device acpi # Advanced Configuration and Power Management device pci # Peripheral Computer Interface (PCI) Bus ############################################################################### # ATA DEVICES device ahci # AHCI-compatible SATA controllers device ata # Legacy ATA/SATA controllers device ada # ATA Direct Access device driver options ATA_STATIC_ID # Static device numbering ############################################################################### # SCSI DEVICES device scbus # SCSI bus (required for ATA/SCSI) device ch # SCSI media changers device da # Direct Access (disks) device sa # Sequential Access (tape etc) device cd # CD device pass # Passthrough device (direct ATA/SCSI access) device ses # Enclosure Services (SES and SAF-TE) options SCSI_DELAY=5000 # Delay (in ms) before probing SCSI ############################################################################### # PERIPHERAL DEVICES device kbdmux # keyboard multiplexer options KBD_INSTALL_CDEV # install a CDEV entry in /dev ############################################################################### # SERIAL (COM) PORT DEVICES device uart # Generic UART bus options CONSPEED=115200 ############################################################################### # SYSTEM CONSOLE DEVICES device vga # VGA video card driver (mandatory!) device sc # syscons is the default console driver, resembling an SCO console options SC_PIXEL_MODE # add support for the raster text mode ############################################################################### # NETWORKING OPTIONS AND DEVICES options INET # InterNETworking options INET6 # IPv6 communications protocols options TCP_OFFLOAD # TCP offload options SCTP # Stream Control Transmission Protocol device pf # /dev/pf and the firewall code itself device pflog # /dev/pflog0 interface which logs packets device pfsync # /dev/pfsync0 interface used for synchronization of firewall state tables options ALTQ # Alternate queuing of network packets options ALTQ_CBQ # Class Based Queueing options ALTQ_RED # Random Early Detection options ALTQ_RIO # RED In/Out options ALTQ_HFSC # Hierarchical Packet Scheduler options ALTQ_CDNR # Traffic conditioner options ALTQ_PRIQ # Priority Queueing options ALTQ_DEBUG # Pseudo devices. device loop # Network loopback device random # Entropy device device padlock_rng # VIA Padlock RNG device rdrand_rng # Intel Bull Mountain RNG device ether # Ethernet support device vlan # 802.1Q VLAN support device tun # Packet tunnel. device md # Memory "disks" device if_bridge # Bridge interface device gif # IPv6 and IPv4 tunneling device faith # IPv6-to-IPv4 relaying (translation) device firmware # firmware assist module device bpf # Berkeley packet filter # PCI Ethernet NICs that use the common MII bus controller code. device miibus # MII bus device re # RealTek 8139C+/8169/8169S/8110S # Wireless NIC cards device wlan # 802.11 support options IEEE80211_DEBUG # enable debug msgs options IEEE80211_AMPDU_AGE # age frames in AMPDU reorder q's options IEEE80211_SUPPORT_MESH # enable 802.11s draft support device wlan_wep # 802.11 WEP support device wlan_ccmp # 802.11 CCMP support device wlan_tkip # 802.11 TKIP support device wlan_xauth # 802.11 WPA security protocols device wlan_acl # 802.11 MAC-based access control mechanism device wlan_amrr # AMRR transmit rate control algorithm device ath # Atheros NICs device ath_pci # Atheros pci/cardbus glue device ath_hal # pci/cardbus chip support options AH_SUPPORT_AR5416 # enable AR5416 tx/rx descriptors options AH_AR5416_INTERRUPT_MITIGATION # AR5416 interrupt mitigation options ATH_ENABLE_11N # Enable 802.11n support for AR5416 and later device ath_rate_sample # SampleRate tx rate control for ath ############################################################################### # UBS DEVICES AND OPTIONS options USB_DEBUG # enable debug msgs device uhci # UHCI PCI->USB interface device ohci # OHCI PCI->USB interface device ehci # EHCI PCI->USB interface (USB 2.0) device xhci # XHCI PCI->USB interface (USB 3.0) device usb # USB Bus (required) device ukbd # Keyboard device umass # Disks/Mass storage - Requires scbus and da ############################################################################### # MMC/SD DEVICES device mmc # MMC/SD bus device mmcsd # MMC/SD memory card device sdhci # Generic PCI SD Host Controller
GPIO
GPIO framework for FreeBSD
Driving Relays from GPIO pins.
FreeBSD GPIO on Raspberry PI
GPIO on ALIX.3D3
Alix 2D13 – FreeBSD – Mode Switch status
io(4) — I/O privilege file
/usr/src/sys ./boot/fdt/dts/beripad-de4.dts ./boot/fdt/dts/ts7800.dts ./boot/fdt/dts/p1020rdb.dts ./boot/fdt/dts/p2041rdb.dts ./boot/fdt/dts/ea3250.dts ./boot/fdt/dts/db88f5281.dts ./boot/fdt/dts/pandaboard.dts ./boot/fdt/dts/digi-ccwmx53.dts ./boot/fdt/dts/dreamplug-1001.dts ./boot/fdt/dts/trimslice.dts ./boot/fdt/dts/zedboard.dts ./boot/fdt/dts/beaglebone-black.dts ./boot/fdt/dts/versatilepb.dts ./boot/fdt/dts/efikamx.dts ./boot/fdt/dts/beaglebone.dts ./boot/fdt/dts/mpc8572ds.dts ./boot/fdt/dts/sheevaplug.dts ./boot/fdt/dts/dreamplug-1001N.dts ./boot/fdt/dts/rpi.dts ./boot/fdt/dts/dockstar.dts ./boot/fdt/dts/exynos5250-arndale.dts ./boot/fdt/dts/p5020ds.dts ./boot/fdt/dts/p3041ds.dts ./boot/fdt/dts/db88f5182.dts ./boot/fdt/dts/cubieboard2.dts ./boot/fdt/dts/db78460.dts ./boot/fdt/dts/beri-sim.dts ./boot/fdt/dts/p2020ds.dts ./boot/fdt/dts/xlp-basic.dts ./boot/fdt/dts/db78100.dts ./boot/fdt/dts/db88f6281.dts ./boot/fdt/dts/am335x-evm.dts ./boot/fdt/dts/tegra20-paz00.dts ./boot/fdt/dts/mpc8555cds.dts ./boot/fdt/dts/cubieboard.dts ./boot/fdt/dts/tegra20.dtsi ./boot/fdt/dts/p5020si.dtsi ./boot/fdt/dts/bcm2835.dtsi ./boot/fdt/dts/p2041si.dtsi ./boot/fdt/dts/p3041si.dtsi ./boot/fdt/dts/exynos5250.dtsi ./boot/fdt/dts/imx51x.dtsi ./boot/fdt/dts/am335x.dtsi ./boot/fdt/dts/imx53x.dtsi
pi@raspberry-pi:~ % dmesg KDB: debugger backends: ddb KDB: current backend: ddb Copyright (c) 1992-2014 The FreeBSD Project. Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 The Regents of the University of California. All rights reserved. FreeBSD is a registered trademark of The FreeBSD Foundation. FreeBSD 10.0-STABLE #31 r266630: Tue May 27 08:43:56 JST 2014 root@raspberry-pi:/usr/obj/usr/src/sys/RPI-B arm FreeBSD clang version 3.4 (tags/RELEASE_34/final 197956) 20140216 CPU: ARM1176JZ-S rev 7 (ARM11J core) Supported features: ARM_ISA THUMB2 JAZELLE ARMv4 Security_Ext WB enabled LABT branch prediction enabled 16KB/32B 4-way instruction cache 16KB/32B 4-way write-back-locking-C data cache real memory = 536866816 (511 MB) avail memory = 484048896 (461 MB) random: <Software, Yarrow> initialized kbd0 at kbdmux0 ofwbus0: <Open Firmware Device Tree> simplebus0: <Flattened device tree simple bus> mem 0x20000000-0x20ffffff on ofwbus0 intc0: <BCM2835 Interrupt Controller> mem 0xb200-0xb3ff on simplebus0 systimer0: <BCM2835 System Timer> mem 0x3000-0x3fff irq 8,9,10,11 on simplebus0 Event timer "BCM2835 Event Timer 3" frequency 1000000 Hz quality 1000 Timecounter "BCM2835 Timecounter" frequency 1000000 Hz quality 1000 bcmwd0: <BCM2708/2835 Watchdog> mem 0x10001c-0x100027 on simplebus0 gpio0: <BCM2708/2835 GPIO controller> mem 0x200000-0x2000af irq 57,59,58,60 on simplebus0 gpio0: read-only pins: 46,47,48,49,50,51,52,53. gpio0: reserved pins: 48,49,50,51,52,53. gpioc0: <GPIO controller> on gpio0 gpiobus0: <OFW GPIO bus> on gpio0 gpioled0: <GPIO led> at pin(s) 16 on gpiobus0 bcm_dma0: <BCM2835 DMA Controller> mem 0x7000-0x7fff,0xe05000-0xe05fff irq 24,25,26,27,28,29,30,31,32,33,34,35,36 on simplebus0 mbox0: <BCM2835 VideoCore Mailbox> mem 0xb880-0xb8bf irq 1 on simplebus0 sdhci_bcm0: <Broadcom 2708 SDHCI controller> mem 0x300000-0x3000ff irq 70 on simplebus0 mmc0: <MMC/SD bus> on sdhci_bcm0 uart0: <PrimeCell UART (PL011)> mem 0x201000-0x201fff irq 65 on simplebus0 uart0: console (115200,n,8,1) dwcotg0: <DWC OTG 2.0 integrated USB controller> mem 0x980000-0x99ffff irq 17 on simplebus0 usbus0 on dwcotg0 fb0: <BCM2835 VT framebuffer driver> on ofwbus0 simplebus1: <Flattened device tree simple bus> on ofwbus0 simplebus1: could not get ranges device_attach: simplebus1 attach returned 6 Timecounters tick every 10.000 msec usbus0: 480Mbps High Speed USB v2.0 ugen0.1: <DWCOTG> at usbus0 uhub0: <DWCOTG OTG Root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus0 mmcsd0: 32GB <SDHC SD 0.2 SN 558891495 MFG 09/2013 by 116 JE> at mmc0 25.0MHz/4bit/65535-block fb0: 1824x984(0x0@0,0) 16bpp fb0: pitch 3648, base 0x5f385000, screen_size 3618816 fbd0 on fb0 vt_allocate: VT initialize with new VT driver. uhub0: 1 port with 1 removable, self powered random: unblocking device. Root mount waiting for: usbus0 ugen0.2: <vendor 0x0424> at usbus0 uhub1: <vendor 0x0424 product 0x9512, class 9/0, rev 2.00/2.00, addr 2> on usbus0 uhub1: MTT enabled Root mount waiting for: usbus0 uhub1: 3 ports with 2 removable, self powered Root mount waiting for: usbus0 ugen0.3: <vendor 0x0424> at usbus0 smsc0: <vendor 0x0424 product 0xec00, rev 2.00/2.00, addr 3> on usbus0 smsc0: chip 0xec00, rev. 0002 miibus0: <MII bus> on smsc0 ukphy0: <Generic IEEE 802.3u media interface> PHY 1 on miibus0 ukphy0: none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto ue0: <USB Ethernet> on smsc0 ue0: Ethernet address: b8:27:eb:xx:xx:xx
Buzzer
APU1C: Using buzzer and LED’s?
PC Engines APU – speaker
FreeBSD Hackers Mailinglist – apu1c led driver
LEDs & Thermal Sensors for APU1C support
PC Engines apu beta test findings
Linux
UNetbootin – create bootable Live USB drives
mSATA SSD
Debian installer USB Stick for PC Engines APU board with mSATA drive
PC Engines APU – Home router replacement
Deban installer CD for PC Engines APU board with mSATA drive
PC Engines APU board: installing Debian on mSATA drive
PC Engines Debian HOWTO
SD card / USB stick
APU + Ubuntu 14.04 LTS – install via serial console
Installation von Ubuntu 14.04 auf PC Engines APU
FDESCFS4>
# mount -t fdescfs fdescfs /dev/fd
mount: fdescfs: Operation not supported by device
options NULLFS # Null-filesystem
options FDESCFS # file-descriptor file system
FreeBSD fdescfs: Operation not supported
A FreeBSD 10 Desktop How-to
Oscilloquartz / OSA
console="comconsole"
search advaoptical.com nameserver 172.21.1.9 nameserver 172.20.1.9
defaultrouter="NO" # Set to default gateway (or NO).
# Device Mountpoint FStype Options Dump Pass# /dev/ada0p2 / ufs rw 1 1 /dev/ada0p3 none swap sw 0 0 fdesc /dev/fd fdescfs rw 0 0 proc /proc procfs rw 0 0
# pw user mod adva -G wheel # chsh